Open top menu
31 Dec 2012
Clue's on Toro Rosso's 2013 Challenger the STR8

2 Italian sources have today ran with the same story on Toro Rosso's 2013 Challenger the STR8:

omnicorse.it
blogf1.it




The two articles circle around the same base principles, that the STR8 will be a new car and distinctively different to the STR7.  The STR7's main differentials to the rest of the field was the high waisted Sidepods.  These compromised the packaging of the radiators and internal components but also damaged the cars CoG a novel concept that was aimed at maximising airflow over the cars floor as much as under it.  Like Ferrari the team with which the car is powered the Launch car (above) was also presented with exhausts that tried to fuse the outgoing Sidepod's airflow with the exhaust plume.  As both found out this gave poor performance in an F1 that now regulated the use of Off Throttle Blowing.  As the season progressed the team assimilated the McLaren ethos with their interpretation of the Coanda exhaust.
Although their sister team and Sauber (also with the Ferrari engine) were having success with the ramped exhaust style without a major redesign they couldn't forge that path.
I'd suggest that with an all new design for 2013 the team will look to use the ramped Sidepod as although the Coanda exhausts were used in the majority up and down the field last season the ramp offers a better baseline and can be improved throughout the season.

The article also mentions the use of Pull rod suspension indicating Ferrari's use in 2012 and that Red Bull's Italian based team will not adopt it for 2013, even though other lead teams such as McLaren and Lotus have hinted they will assess it's merits.  Ferrari's adoption of pull rod suspension at the front of the car was not only introduced for it's aerodynamic qualities but to aid in both the lowering of CoG and treatment of the Pirelli tyres.  The latter a massively important part of the 2012 challenge for the teams aided Ferrari in their quest for front end grip.  The 2012 Pirelli tyres construction led to a much narrower contact patch which the pull rod arrangement may have assisted with, allowing for a better initial heat cycle and lengthened operating window when driven correctly.  With Pirelli already stating their 2013 construction widens the contact patch the mechanical gains from pull rod front suspension may have narrowed, the teams had the opportunity to see this first hand in Free Practice at Interlagos:  http://somersf1.blogspot.co.uk/2012/11/pirellis-2013-test-tyre-brazil.html

In an interview with Autosprint Daniel Ricciardo had this to say: "I can tell you I've already seen it and, when looking at it closely, it's very different from the old one,"



Above: The team didn't hold back when they tested at Abu Dhabi either evaluating what could be a Dual DRD (Drag Reduction Device) perhaps one of the key elements required for success in 2013.

It will be interesting to see how much influence James Key has had since his arrival at Toro Rosso from Sauber but one things for sure the team seem intent on closing the gap to the front runners.  Their recent announcement that they will run Renault engines for 2014 also raises the question of whom will supply their Gearbox and KERS. The obvious choice is a reunification of the Red Bull Racing partnership with Toro Rosso receiving parts from the team just as Caterham purchase theirs.




Read more
30 Dec 2012
Red Bull Racing - Historic / Technical Assessment - Part 2 2009-Now

I have already covered the early years of Red Bull Racing in Part 1: Red Bull Racing - Historic / Technical Assessment - Part 1


2009 - A New Era in F1

2009 marked a new era in Formula One with a set of technical regulations that would alter the face of the racing and displace some of the old guard from the top branches. Red Bull had been busy preparing themselves for a number of seasons in preparation for the task at hand taking huge strides in the way in which they approached both design and development. Their infrastructure be it technical staff or facilities now rivaled if not exceeded some of the top teams and allowed them to steal a march in 2009. The technical regulations outlined by the FIA for 2009 were designed to make the cars more sparse, reducing the effects of 'Wake' so that cars could follow each other more easily. The most obvious visual changes were the lower and wider Front Wing and the shorter and taller Rear Wing. Slicks made a welcomed return to F1 which again would alter the racing dynamic affording more mechanical grip. Intent on making F1 a motorsport category that once again involved close wheel to wheel racing and overtaking the FIA also allowed the Front Wings flap to have a 6 degree movement. Engine rev limits were reduced to 18,000rpm and each driver now had an 8 engine allocation for the entire season. KERS also featured for the first time in 2009 allowing those cars equipped with the 80bhp boost around 6 seconds of additional power. Track testing which had allowed the front runners to stay ahead for many seasons would now be halved from 30,000 KM to 15,000 KM and could not be conducted throughout the season. Wind Tunnel testing that was also an expensive commodity could only be run at a maximum of 50 metres per second with a 60% model. (4 hours of Full Scale Wind Tunnel testing could however be traded for one of the 4 permitted days of straightline testing)

The retirement of David Coulthard at the end of 08 paved the way for the raw pace of Red Bull's starlet Sebastian Vettel who had impressed hugely whilst at the wheel of the Toro Rosso.

2009 - RB5

We all know of the arguments that ensued at the beginning of 2009 when BrawnGP, Toyota and Williams had exploited a loophole in the new rules to use Double Decked Diffusers. This led to those teams having an advantage at the start of the season whilst the others went off to redesign their own iterations. Red Bull were one of the teams that lobbied for the DDD's to be banned as they knew that implementing it on the RB5 would lead to a compromised design. This was firstly blamed on the introduction of pull rod suspension on that years challenger which lowered the centre of gravity but was said to encumber the airflow to the DDD if applied. The pull rod suspension was not the only reason that using the DDD on the RB5 would be difficult the design of the gearbox which was also lowly slung was also essential in how the airflow path utilised the top deck. Brawn GP had been eager to use the Carbon Fibre casing designed in the Honda days in the BGP-001 to this end.

Even without the DDD it was clear the RB5 was the best of the Newey designed Red Bull's thus far with the teams first 1-2 coming in China. The car featured elements not seen on other designs with a ridged nosecone and extremely sculpted Sidepods that left the exhaust to exit just under the upper wishbone. Newey and the design team also took the wording around the Rear Wing Endplates and Diffuser to it's usual limits by extending the Endplates down to form part of the Diffuser.

The diffuser stole the limelight in 2009 which clouded the effects seen by both mechanically and aerodynamically by the switch to slick tyres. The reintroduction of slick tyres was just one of the measures both the FIA and TWG believed could reinvigorate the wheel to wheel racing in F1. Tyres are the unsung heroes in terms of the racing element and can make a huge difference to a cars design. Undoubtedly Bridgestone would have adopted a different ethos when designing their Slick tyres, both different compounds and the tyres construction would differ from the ones used with their grooved tyres. The media are always quick to talk about the downforce being generated by the cars most likely as they feel this is quantifiable to the fans. The role the rubber plays however can be just as important as it too can have an effect on the aerodynamics and the downforce that can be generated. Understanding the tyres dynamics also helps to setup up the cars suspension which in turn can provide a performance advantage by decreasing wear life.

In stark contrast to the established frontrunners the RB5's wheelbase was quite a margin longer which would have an impact on weight distribution, suspension setup and of course aerodynamics. Whilst the other teams had utilised the DDD loophole in order to increase the height of the Diffuser Red Bull expanded the diffusers size by lengthening the area with the Rear Wing Endplates. As the team had plenty of space left either side of the Rear Wing Endpates (As their Diffuser didn't stretch to it's maximum permissible size) they attached footplates between the Endplate and the Wheel in order to create a lengthened vortex managing the effects of Tyre Squirt on the Diffuser. The original footplates from the Jerez test were simply flat but when the car arrived in Australia they had a distinct arc to them.

Above: With the RB5 side by side with the McLaren MP4-24 we can see the different Rear Wing and Diffuser Ethos' at play, with McLaren using a much wider Diffuser area. The footplates mentioned above have been arrowed

Although the RB5 didn't feature it in it's launch spec by Melbourne the team had added a shark fin, unlike the fins that featured on the likes of the Renault R29 though the RB5's stretched all the way to the top flap of the rear wing connecting the two.

Above: The RB5's Rear Wing Connecting Shark Fin

Carried across from the last regulation set was the use of Wheel Covers, these help manage the airflow around the wheel.

In Malaysia the team introduced a hole in the floor just in front of the rear tyre, this was placed here to create a vortex which in turn would aid in the Diffuser's efficiency.
 
Above: Giorgio Piola Illustrates the hole created in the RB5's floor from Malaysia onward

The RB5 originally featured mirrors on stalks that connected to the outside edge of the Sidepod in order to clear the usual space they occupied next to the cockpit for better airflow. Outboard mirrors as they became to be known had been a feature of the Ferrari F2009 since the start of the season and mounted the mirror directly to the Sidepod Airflow Conditioner. Red Bull followed suit in Barcelona further clearing the Sidepod of intrusions.

Furthermore in Barcelona the team added a hole in the central 15cm exclusion zone of the top flap this would allow for a steeper AoA making the wing more efficient.

Above: Red Bull RB5 at Barcelona with their newly positioned Wing Mirrors and centralised slot in the Rear Wing's top flap

The team introduced their interim DDD at Round 6 in Monaco which featured the higher deck exiting either side of their low slung gearbox/crash structure.
Above: The damaged RB5 is lifted off the track at Monaco affording us the opportunity to see the channels used by Red Bull to feed their upper deck of the Double Diffuser
Above: The New DDD exited centrally above the main diffuser. Also very noteworthy in this picture is something that I think has often been overlooked in Newey's designs and that’s the halfshaft covers (Shroud). Here on the RB5 (Arrowed) they extend to cover the central portion of the Diffuser limiting the exhaust plumes influence on the Magnus Effect created by the halfshafts. (A rotating part creates downforce which is fine if the airflow to the rotating object is continuous and laminar) The placement of the exhaust on the RB5 without this shroud would leave the halfshaft exposed to the inconsistent and erratic exhaust plume. By placing this shroud over the halfshaft it isn't exposed to an inconsistent airflow pattern and so continues to provide a consistent level of downforce of it's own.

The largest revisions however came 2 races later at Silverstone when the team introduced a new nose which was much wider than it's predecessor and placed the FOM camera's either side of the nose tip immediately bringing to mind the image of a Hammerhead Shark. The nose profile suddenly became the widest in the field and this change of ethos would change the aero further downstream (The team did continue to use the slimmer nose at several GP afterward). To tie in with this change at the front of the car the team revised the rear layout reducing the height of the Rear Wing Endplates and increasing the width of the diffuser. An expanded central section in the centre of the Diffuser helped to maximise the DDD effect with the RB5's configuration.

Above: Sebastian Vettel crosses the line to take victory at Silverstone the new wider Nose is easy to see in this image

Above: As the Red Bull driver is congratulated by his team we can see that they are now running a revised Rear Wing Endplate and Diffuser configuration

The Front Wing of the RB5 changed frequently throughout 2009 but a significant change came in Spa when the team adopted the type of Cascades that we still see on the cars up and down the grid today.

Above: We can see in this image that not only did the team revert back to the slimmed nosecone for Spa they introduced their Front Wing Cascades. The Cascade still provided a platform for the bridge wings to extend from too

BrawnGP's early advantage allowed them the required buffer to take both 2009 Championship's but it was clear to see that Red Bull's investment in the proceeding seasons was starting to pay dividends. With 6 race victories and 16 Podium visits in total between their 2 drivers it was clear to see that the team now had the core strengths with which to win Championships. Only a bad start to the season for the young German tied in with Their Achilles heal (reliability) meant the Red Bull team fell just short of taking the titles in 2009. Their development push on the RB5 throughout 2009 stood them in good stead for 2010. BrawnGP completed a late deal that was to put them into Mercedes ownership for 2010 but due to the reverse fortunes of Red Bull in terms of funding and staff they would fall away for 2010. ( I wrote about this in a previous article: The Trouble at Mercedes)

Above: Toro Rosso's 2009 Challenger the STR4 seemed from the outside to be a replica of the RB5

For 2009 the Toro Rosso team fielded the Sebastians of Buemi and Bourdais the latter however made way for Jaime Alguersuari from Hungary onwards. 2009 provided the backdrop to an uninspiring season from the Red Bull B team with only 6 points finishes leaving the team at the bottom of the Constructors table. The STR4 was essentially a RB5 but failed to come even close to the performance of it's Renault powered sibling.

2010 - RB6

Although on the face of it the cars didn't seem distinctively different for 2010 there were some fairly large design considerations to take into account. Firstly re-fueling was banned and so the cars would need to carry enough fuel to complete the whole race. This would have an effect on both the balance and wheelbase of the cars. Wheel Covers that had now become complex aerodynamic devices were banned and in an effort to reduce grip levels following the switch to Slick tyres in 2009 the Front Tyres were reduced in width from 270mm to 245mm. Renault were allowed dispensation by the FIA/Teams to work on their engine to bring it inline with the competition something that proved vital in Red Bull's progress. KERS proved somewhat of a damp squib in 2009 with both Brawn & Red Bull not opting to use it throughout the season even though the cars had been designed with it in mind. With 3 new teams entering the sport the teams took the decision not to run the system at all in 2010 but refine the concept for it's reintroduction in 2011. After the controversy of 2009 the teams were allowed to continue usage of the DDD's with a ban coming into effect in 2011. This allowed all the teams to fully commit to this design path for 2010 with Red Bull opting to not only use the space above as a secondary deck for the diffuser but also feeding it with airflow from the Sidepods / Radiators. The design team raised the Gearbox / Crash Structure on the RB6 to allow for a much cleaner airflow path for their DDD.

Above: On the underside of the car the RB6 featured a much larger entrance to their second deck than any of the other teams.

Several developments arose during the early stages of 2010 with Red Bull triggering the development path of one of these with their Exhaust Blown Diffuser. The team tested with a similar configuration used on the RB5 but when the teams arrived in Bahrain Red Bull had another exhaust up their sleeves. The RB6's exhaust now lay to the bottom rear of the Sidepod and would send it's exhaust gasses between the edge of the floor and tyre. This would create a spiral effect which would seal the diffuser at it extremities allowing for a much more productive Diffuser. Once again this allowed Newey to shroud the inner part of the halfshafts removing them from the inconsistent exhaust plume. With the central portion of the Diffuser isolated a window was opened up in the outer section of the diffuser in order to extract more performance from the exhausts energy.

Above: The RB6 looked remarkably like it's predecessor the RB5 but as we can see in this picture the exhaust was positioned low on the floor in order to help maximise Diffuser performance

Above: A window of opportunity, with the central portion of the diffuser isolated this window in the outer section of the diffuser allowed the exhaust plume to further influence performance

Furthermore Red Bull used Off Throttle Blowing during qualifying in order to extract more performance. Off throttle blowing enables a more consistent exhaust plume, as the driver comes off the throttle the engine map retards the ignition and with the exhaust valve open the explosion happens in the exhaust rather than being used to drive the piston down. This is known as Hot blowing and can over a sustained time frame be detrimental to engine performance. All in all the driver gets more downforce when he needs it in the corners.

Above: In China the team introduced under nose Turning Vanes, these L shaped appendages would help to manage the airflow under the central portion of the car and deter any errant airflow from the wheels to impinge on it.

The other device that had caused a stir when McLaren started testing was their RW80 or F-Duct as the mainstream media coined it. The device reduced drag on the Rear Wing by Stalling the plane it was attached to but was controversial due the need of the driver to cover a hole in the cockpit. It's integration into the other cars would be a long winded process as they set about routing the pipework through the car. Sauber were the quickest off the mark with their own version being ready for Round 2 at Melbourne, Red Bull first tested their own iteration in Turkey but didn't race it. The team also introduced a new Front Wing in Turkey featuring a hole in the Endplate that would allow air to move between the two sides, but just like the F-Duct this was only used in Practice as they reverted to the old specification for the race and qually.

 
Silverstone provided the backdrop for another significant alteration to the front of the RB6 with the FOM camera's being relocated low between the pylons and aft of the FIA mandated Front Wing area. Alterations were also made to the Endplates which now featured 2 holes allowing air to pass between the 2 sections and making for a more efficient assembly. This would however lead to a somewhat frosty relationship within the team. As when Sebastian damaged his new version of the front wing in practice, the team decided to take the only other iteration of the wing available from Mark's car and place it on Seb's car. This seemingly set the tone in the team and marked the first major rift to appear in the Red Bull façade. Webber went on to win the race at Silverstone even without the seemingly quicker Front Wing and remarked on the radio on his in-lap: 'Not bad for a number 2 driver, eh?'
It's clear to see why Mark would be so frustrated as the senior driver up until Silverstone he was only 12 points adrift of his German counterpart and both still within touching distance of the 2 McLaren drivers.

Above: The controversial Front Wing featuring 2 Endplate holes and the placement of the FOM carmera's to the lower position between the wing pylons.

As the season moved on it became obvious that Red Bull had devised a way in which to make the Front Wing flex whilst still passing the FIA's load tests. This flexibilty allowed the tips of the wing to flex down toward the track, of course all wings flex but Red Bull had used techniques they had been honing in order to circumnavigate the FIA load tests. The tests carried out initially in 2010 saw a 50KG force applied to the Endplate allowing a 10mm flexing tolerance. The FIA altered this from the Belgium GP to 100KG of force with a 20mm tolerance. The flexing Front Wings became an area for the other teams to chase with Ferrari perhaps sticking in the memory for their 'fluttering' wings. The principal behind the flexibility was to change the characteristics of the Wing creating a skirt as the cascade droops to the ground.

Above: In Singapore the team introduced a new F-Duct system utilising the mainplane rather than the top flap. Combined with this they returned to using a hole in 15cm central portion of the top flap to aid efficiency.  Adrian also inspects the effects of the New Beam Wing configuration being used with flo-viz indicating it's effectiveness.

The team took 9 victories in 2010 and with a further 11 trips to the podium the team clinched the Constructors title at Brazil where the team completed a 1-2 finish creating an insurmountable lead. Meanwhile the driver's title was a hard fought battle between the two Red Bull drivers and Ferrari's Fernando Alonso. The Driver's title went to the last race in Abu Dhabi where Sebastian crowned a great season finishing 1st. A frustrated Alonso finished in 7th having spent a large proportion of the race behind the Renault of Petrov awarding Sebastian the title by just 4 points.

2010 marked the first time since Red Bull had taken ownership of the Toro Rosso team that it must design and build it's own car. The teams facilities in Italy took care of the build of the car whilst the Wind Tunnel facilities the team also owned in Bicester (Left over from the Jaguar purchase) were also put to use. At this juncture I believe Red Bull and Toro Rosso's histories fail to align and so I won't cover their progress here on in.

2011 - RB7

2011 saw the teams adjusting to more regulation changes with the proposed banning of DDD's (Double Decked Diffuser') being implemented with Diffuser height being shrunk from a maximum of 175mm to 125mm. The F Duct that was pioneered by McLaren and copied by most of the field throughout 2010 was outlawed but having seen the potential for reducing drag at the rear wing the FIA ushered in DRS (Drag Reduction System). The new system allowed the driver to change the angle of the Rear Wings top flap in order to shed the drag induced by the wing. It's use would be unlimited during Free Practice and Qualifying but could only be used in certain zones throughout the race. Bridgestone withdrew from F1 at the end of 2010 which made way for Pirelli to join the fray. Pirelli promised a much more aggressive approach to tyre selections than it's predecessor which in turn should have led to better racing. To assist Pirelli the FIA also mandated the Weight Distribution of the 2011 challengers. KERS (Kinetic Energy Recovery Systems) also made a return to F1 with the technology having been worked on by the teams and engine manufacturers throughout 2010.

With DDD's banned the team could once again return to the RB5's ethos of a low slung gearbox and crash structure lowering the CoG. What it did carry over from the RB6 however was it's low slung exhaust aimed at driving air through the diffuser. Red Bull had enhanced the concept by shrouding the exhaust in a tunnel that lead the exhaust plume to both flow between the Diffusers edge and the tyre and also blow through the aperture in the outer 5cm of the Diffuser. (Half over the floor and half under it, aiding in the prevention of tyre squirt by sealing the edge of the Diffuser)

Above: Craig @ScarbsF1 Scarborough's image above depicts the RB7's Exhaust Blown Diffuser (EBD) the full article from Craig is available here: ScarbsF1.com

Red Bull's EBD was readily copied by the other teams who also had one eye on Renault's FEE (Front Exit Exhaust) but as with everything in F1 the team who adopts something first is usually the only one to fully extract it's potential. With a fully integrated EBD the airflow being seen by the halfshafts no longer became a threat and so the shrouding they received in the RB5/6 forms were removed gaining another element from which to create downforce. The Diffuser saw some alterations for China with the outer sections being reduced in height meanwhile a perforated gurney was added to the inner section. (Below)

The FIA grew weary of the teams pursuit of exhaust gas manipulation via engine mapping quite early into the 2011 season and moved to ban it's use. After much too-ing and frowing with the teams, engine manufacturers and FIA the ban was lifted for 2011.

At the front of the car the team returned to the Hammerhead layout with the FOM cameras either side of the nose tip. Effort was still being placed on finding ways to flex the front wing even with more restrictive load tests.
Above: Sebastian negotiates the Melbourne Circuit, the RB7 features the FOM camera's in the Hammerhead/Handlebar position once more

Above: At Valencia a new set of turning vanes were introduced in order to better maximise the flow under the nose

Above: As always the team tried different Front Wing configurations throughout the season with perhaps the notable iteration coming in Singapore.  The Front Wing introduced in Singapore featured 2 distinct alterations: Next to the mandated central portion of the Mainplane the wing arced, this creates an elongated vortex that I'd imagine was designed to help control airflow transmitted from the tyres. Next to the usual Cascade arrangement a new R Cascade had also sprouted up, this cascade would work in unison with the flaps tip behind it to create a stronger spiraling vortex

Strategy had become less important throughout 2010 due to the lack of refuelling and lack of hard tyre choices by Bridgestone. This changed for 2011 with Pirelli's entrance to the sport increasing tyre degradation levels and requiring both the drivers and teams to react differently. Red Bull's superior downforce levels compared to the rest of the field didn't mean they had less of a challenge with the tyres just a different scale. Red Bull did however push their luck a little too far in Spa when they blistered their tyres in qualifying. Red Bull asked that they be allowed to run with a new set of tyres at the start of the race but the FIA declined as Pirelli had been recommending maximum camber with which to run and the team had ignored.

The team had KERS onboard for the first race in Melbourne (having not used it throughout 2009) but due to reliability issues they decided not to use it until Malaysia. It didn't stop Sebastian taking the first victory of the year though. KERS continued to be Red Bull's Achilles heel with Newey even remarking that he'd prefer not to run it, which obviously stems from his clear favour of aero. KERS compromises the aero package due to both it's physical properties and cooling requirements both of which disturb Adrian. Even with lingering KERS problems the team were dominant with Sebastian finishing on the podium in all but two races (4th in Germany and a DNF in Abu Dhabi) taking both titles again and completing the double, double.

2012 – RB8

The RB8 was another evolution of the RB5 concept, refinements came in the form of 2012's controversial Step Nose and Sidepod Airflow Conditioners that now arched to meet the top of the Sidepod. In the case of the RB8's step nose the team had used the area as for driver cooling taking an advantage of an area that would otherwise impact on the airflow over the top of the cockpit.


Red Bull had been at the cutting edge over the last few seasons utilisng Exhaust positioning and clever engine mapping in order to enhance their aerodynamics. The technical regulations for 2012 would however put pay to this progress with the exhausts now required to exit atop of the Sidepods. The Red Bull team had reportedly spent some of their development time chasing a method of re-ingesting the exhaust gases above the central portion of the Diffuser which would lead to nearly the same levels of downfroce seen in 2010/11. The FIA duly outlawed the design before it even hit the tarmac leaving the team to redesign their 2012 challenger.
When the teams arrived at testing it was clear that several options had been pursued but as usual the Red Bull design team were not showing their hand early on when they arrived in Jerez with an exhaust reminiscent of the RB5's placed just under the upper wishbone. 

Above: The exhaust solution tested by RBR at the first test in Jerez was aimed at the Beam Wing

Once again the team were intent on removing the Magnus effect and it's interaction with the exhaust plume and so the RB8 featured a full length halfshaft shroud. This could be seen at the Jerez and was an indication that the exhaust featured above was a Red-Herring.

Above: Red Bull's first test with the RB8 showed the team using a full length halfshaft shroud in order to remove the Magnus effect from the equation. This picture also shows the new Diffuser and full length perforated Gurney that the team would adopt for 2012. The Rear Wings endplates were now attached further forward to allow for the Gurney

When the team arrived at the final test in Barcelona the RB8 sported a new rear end with the exhaust placed extremely far forward on the Sidepod in a ramped configuration. The exhausts positioning would utilise the airflow downwashing over the Sidepod sending it over the top of the diffuser and into the gap between the floor and tyres that the EBD's of 2010/11 had previously done. The ramp used on the RB8 also prohibited the flow from around the Sidepod interacting with the exhaust plume in a way which would be detrimental but this is where the team pushed the regulations further. A Tunnel toward the rear of the Sidepods ramp allowed air to migrate underneath the ramp and exit into the exhaust plumes natural flow.

Above: The RB8's configuration in the last Barcelona test as we can see the tunnel exits just infront of the pull rod into the exhausts flow.

 
Above: Added to the RB8 with the new exhaust iteration was 2 floor mounted strakes underneath the shrouded halfshafts. These were placed here to guide the airflow as it passed over the region.

The RB8's exhaust solution was complicated and although CFD and Wind Tunnel had clearly simulated it's merits on track the drivers complained of inconsistencies. This didn't stop the team from taking 2nd and 4th for Seb and Mark respectively in Melbourne. The team revised the exhaust channel for Malaysia opting for a more square edged channel which would change the way in which the exhaust plume interacted with the surrounding airflow. But whilst Mark continued in the same vein with another 4th place Sebastian languished outside the points in 11th having collided with Karthikeyan whilst he had been placed 4th.

For China the team decided to split their strategies as Seb still struggled with the exhausts inconsistent nature. This reminded me of a piece I had read by Mark Hughes during 2010 when Red Bull introduced their Exhaust Blown Diffuser:

At this part of the season, Webber was genuinely able to get more from the car's exhaust-blown diffuser.

In its initial form, this component required a very specific driving technique to maximise the time on open throttle - which increased the downforce boost from the exhaust plume - and Webber was superb at it, consistently squeezing just that little bit more from it than his team-mate.

Vettel continued to be better at living with a little bit of entry oversteer, and that ability to adapt to the car moving around him was maybe partly why he was not as insistent on adapting his technique to a feature that calmed the rear end as soon as you got on the throttle.

From Valencia onwards however, the Renault engine was running software that retarded the ignition off-throttle, using the extra heat created to maintain exhaust flow to the diffuser even off-throttle. 

Suddenly that downforce boost was there even during braking and Webber's specialised technique was no longer required. That improvement, in other words, took away a key Webber advantage.


 
Above: Sebastian ran the exhaust configuration seen in pre-season testing at China, the exhaust is placed toward the rear of the car just below the suspension arm using this as a deflection tool to push air downstream. This configuration (due to the exhaust layout) has a much longer sidepod region which means the airflow has to travel much further down the car before it interacts with the exhaust airflow. Having the exhaust in this position is much more neutral and will give a less ‘twitchy’ car however net rear downforce could suffer.

Above: Post race at China we can see that Mark's car now features a much more squared off Exhaust channel

3rd time lucky? At Bahrain the team introduced their 3rd exhaust solution of 2012 which had the tunnel closed off. This design was the same as the one on the Sauber C31 and removed the inconsistencies that the tunnel was creating both off throttle and in yaw.

Above: Sebastian takes his first victory of the season in Bahrain meanwhile his team mate took his fourth, fourth place of the season

The team also adopted a similar solution being implemented on the Sauber in front of the rear wheels with a duct next to the vertical strake. The idea behind these are to reduce Tyre Squirt which is an unwanted aerodynamic effect of the rotating wheel/tyre. As the air dissapates from the wheel/tyre it is sent laterally into the diffuser's flow disrupting downforce. The holes/slots manage the airflow coming off the wheel/tyre and reduce the effects of squirt.
Above: The Tyre Squirt duct in use in Bahrain

Sandwiched in between Bahrain and the next round in Barcelona was the first in season test for 4 years taking place at Mugello. Red Bull had stated they saw no reason for in season testing and it was an expense that the team was bearing for little gain. They tested but provided no clues to what we could see in the forthcoming races instead concentrating on correlation work and tyre setup. One surprise did however come out Mugello with Caterham attempting a Red Bull style tunnel, they didn't waste huge chunks of time evaluating the option though and it didn't see the light of day again
 
Above: The Caterham CT-01 featured a Red Bull style cross-under tunnel in Mugello

In Barcelona the team returned to using the cross-under tunnel Sidepod but this time the tunnel had been extended and instead of releasing the airflow into the exhaust plume it would now be funnelled and released through the engine cover and out the back of the car.

Above: The elongated Tunnel now directed airflow entering it into the Engine cover and most likely exited the flow through the Starter Hole a rare glimpse of which was captured below by AmuS. As we can see in the picture above even with the use of the cross-under tunnel back the team continued to use the Tyre Squirt duct too
 
By this stage the team had added more control fins under the halfshaft shrouds with 2 now either side of the car. Furthermore a re-ingestion hole had appeared in the floor of the RB8 aft of the pull rod aiding flow to the central portion of the car.


Monaco saw the Tyre Squirt ducts on the RB8 come under scrutiny with most of the teams contesting their legality. Unlike the ones on the C31 and F2012 Red Bull's did not break the floor at it's edge which effectively makes theirs a duct and not a slot. At the time I wrote the following articles detailing it:


As the Red Bull style duct was outlawed the team went to Canada with their ramped style exhaust that didn't feature the cross-under tunnel but ever eager to understand and learn the team used a rather impressive Pitot Tube array on the car during the Free Practice sessions.


 
Having taken pole in Montreal I remarked at the time I believed Sebastian had taken too much from the tyres. This proved to be the case and his race result was further compromised when the team tried to eek out his stints demoting him to 4th as both Grosjean and Perez passed the German on fresher rubber.

A two week break after Montreal and the return to Europe in Valencia awaited the teams, Red Bull had been busy back at the factory and arrived with what could have been classified as a B-Spec car.
So much so that even though I do a Technical Roundup post GP I felt compelled to specifically cover the RB8 on it's own - http://somersf1.blogspot.co.uk/2012/06/red-bull-valencia-gp-technical-analysis.html

The RB8 now featured a expanded version of the cross-under tunnel with which 2 entrance/exits were in use. Vortex Generators had been added to the top of the Sidepod in order to further enhance the 'downwash' that lead to the exhaust channel. Another pair of vertical floor strakes were added under the halfshaft shrouds (now with 3 either side) to groom the airflow.
Above: The new Sidepod ramp for Valencia which featured 2 Tunnels

The pace of the Red Bull's in Valencia was quite frightening when compared to that of it's rivals with Mark's pace disguised by his lowly starting position of 19th. He finished the race in 4th but his team mate failed to finish due to an alternator failure, a gremlin that would also force the Renault powered car of Grosjean's to a DNF.
  
Above: For Silverstone the team revised the channel around the exhaust creating a hump in order to encase the airflow.

 
Above: In order to further extract performance from the exhaust the team also used a Resonator Chamber which I wrote about at the time: http://somersf1.blogspot.co.uk/2012/07/red-bull-exhaust-resonator-expansion.html

At Hockenheim the team became embroiled in yet another technical infringement, this time centered around the use of torque maps. The FIA technical delegate Jo Bauer made this statement: “Having examined the engine base torque map of car numbers 01 and 02 it became apparent that the maximum torque output of both engines is significantly less in the mid rpm range than previously seen at other Events. In my opinion this is therefore in breach of article 5.5.3 of the 2012 Formula 1 technical regulations as the engines are able to deliver more torque at a given engine speed in the mid rpm range. Furthermore this new torque map will artificially alter the aerodynamic characteristics of both cars which is also in contravention of TD 036-11. I am referring this matter to the stewards.”

3 hours after Jo's report was released the stewards responded with:

The stewards received a report from the FIA Technical Delegate, along with specific ECU data from Red Bull Racing Cars 1 and 2. The Stewards met with the team representatives and the representative of the engine supplier Renault.
While the stewards do not accept all the arguments of the team, they however conclude that as the regulation is written, the map presented does not breach the text of Art. 5.5.3 of the Formula One Technical Regulations and therefore decided to take no action.”

Effectively the stewards were saying that although Red Bull were breaking the rules per-se the way in which the rules had been written still allowed what Red Bull were doing. This led the FIA to ratify the rules after the GP requiring a torque map to be selected by each team from the first 5 races of the season and giving a target % to work within that map. Essentially the map used by Red Bull in Hockenheim limited the torque available to the driver by offsetting the pedal position to the power being produced. This aided in both increased drivability and a more continuous exhaust airflow allowing the exhaust gasses to provide aerodynamic advantage even when the driver was curtailing his throttle usage.

This didn't adversely effect Red Bull who went on to score good points up until Monza where the curse of the Renault alternator struck Sebastian Vettel again giving him another DNF.

Singapore represented another fairly large shift for Red Bull with another package of upgrades they flew out a new Nosecone/Front Wing which represents a change in philosophy, the Top Flap now separates into two sections making the Wing 4 tiers as opposed to 3. The tips of the Top Flap in combination with the R Cascade in front of it are designed to vorticise the airflow leading to a more energised flow being dispatched along the car.

In Tandem with these Front Wing changes the team also revised the nosecone of the RB8 utilising a 'Pelican' style underbelly to the nose whilst extending the tip of the nose and also placing the FOM Camera's into a more forward and lower position. Red Bull have adopted the hammerhead camera placement since Belgium tidying up the area between the Front Wing Pylons and allowed for the introduction of the Tilting or Rotating Wing and 'Pelican' underbelly. Like most teams Red Bull originally used the camera's in a position behind the central section of the Front Wing to attenuate the airflow's characteristics. This is important as the central portion of the Wing is an area subject to specific rulings set out by the FIA in order to the limit the amount of downforce/effect generated here however with a Lower Nose tip and 'Pelican' underbelly the effect has been altered higher up.

Above: In the image above I've overlayed a picture of the RB8 from Hungary (Right) with an image from Suzuka. The Green arrows depict the placement of the FOM camera's, Yellow arrow's show the difference in the Top Flap and I've lightened the area under the nose on the left and marked it with a Red arrow to show the 'Pelican'. (The image will never give a 100% accurate impression of the as they are taken from different distances/angles and the car is in different stages of inertia but I feel it gives an idea of what you should be looking for)

Above: Also introduced in Singapore was Red Bull's DDRS (Double DRS) pioneered by Mercedes at the start of the season Red Bull's version simply augmented flow at the rear of the car rather than via tubing to the Front Wing. My article from the time on RW-DDRS can be found here: http://somersf1.blogspot.co.uk/2012/10/red-bull-rb8-rw-ddrs-plausible.html

Above: The team also reduced the length of the Rear Wing Endplates Strakes

Red Bull continued their technical assault when they introduced another version of the Exhaust Ramp / Cross-under Tunnel in Korea. The ramp was much shorter and seemingly moved the exit of the airflow from directly at the Starter Motor Hole to either side of the Engine Cover. I covered this here: http://somersf1.blogspot.co.uk/2012/10/india-gp-technical-roundup-ferrari-red.html

Abu Dhabi and Interlagos featured some of the best driving and strategic calls we have seen from Sebastian and Red Bull respectively. Abu Dhabi however became another source of speculation in regard to the use of Flexing materials at the front of the RB8. I covered both the race from Seb's perspective and the issue of flexing Nose/Wings here: http://somersf1.blogspot.co.uk/2012/11/abu-dhabi-gp-vettels-rise-red-bulls-fall.html

The last race of the season put Sebastian within touching distance of a 3rd title with the Constructors having been sown up in Austin. The race didn't get off to a great start when he collided with Bruno Senna but it did lead to a great spectacle for the fans. I covered the damage and race from Seb's perspective here: http://somersf1.blogspot.co.uk/2012/12/a-deconstruction-of-brazilian-gp-from.html

Conclusion

Red Bull's early adoption of a longer wheelbase with the RB5 helped with the transition from the re-fueling of 09 to the full tanks of 10. Their understanding of the slick tyres also provided the team with a great platform on which to work but it was their unwavering will to push the boundaries of both the technical regulations and implementation and marriage of new and old technologies in combination in order to extract more performance from their cars that has ultimately made them a force to be reckoned with. A superb infrastructure in terms of both staff and facilities sets the team in good stead for the future and with a stable rule set for 2013 I see no reason why the team won't once again be challenging for both titles.
Read more
26 Dec 2012
Red Bull Racing - Historic / Technical Assessment - Part 1 2005-2008

The Team, Personnel and Facilities

Red Bull's roots in F1 can be traced back much earlier than it's team ownership with the brand using F1 as a platform to advertise it's energy drink as far back as 1995, with it's logo's adorning the Sauber C14. The partnership continued through until 2005 when Dietrich Mateschitz elected to purchase the Jaguar Racing outfit from Ford (The team was purchased toward the end of 2004) and use F1 as a vehicle for further enforcing their brand globally.

Above: The Sauber C14 featured Red Bull livery in 1995 and continued to do so through until the C23 of 2004

The newly founded Red Bull Racing team would race the Jaguar designed chassis in 2005 mated to a 3.0 V10 Cosworth engine continuing the collaboration the Jaguar team had when it took over from Stewart Grand Prix in late 1999. Mateschitz had given Dr Marko Helmut an advisory role with the team who installed Christian Horner as Team Principal ousting Tony Purnell who had been seen as one of the key figures in Jaguar Racing's turn around in the preceding seasons. Horner himself had raced in lower formulae, but as he moved through the ranks to F3000 and founded the Arden Racing team he realised that management could be more his forte. The symmetry of Horner's success can now be seen, with the early years in F3000 like a new born breaking their teeth they struggled to stamp their mark. However as time went by the results started to flow with the team collecting titles in 2002, 2003 & 2004 and their drivers Wirdheim and Liuzzi taking drivers titles in 2003 & 2004 respectively.

It was the core values of understanding that you need the right people around you that Christian had forged in F3000 that I believe bought him to Red Bull's attention. His ability to spot and nurture talent was also important to a Red Bull brand that also thrives on it's youthful outlook. Christian's own youthful exuberance would form the basis for the direction the team would take, allowing a relaxed but pragmatic environment in which the talent they already had and would entice could thrive.

Christian has continued his work with Arden International in combination with his Red Bull endeavours, even though Arden has failed to replicate the Championship winning years they do provide a platform for young drivers to ascend to F1. Having seen 6 of their drivers already reach F1 (Liuzzi, Kovalainen, Bruno Senna, Buemi, Perez and Pic) they are still nurturing talent through their GP2, GP3 and Formula Renault 3.5 programmes. The GP3 team is MW Arden born from the connection with Red Bull's senior driver: Mark Webber fortifying the brand and giving another avenue in which to groom talent. For 2012 Arden collaborated with Caterham competing in the World Series by Renault allowing Caterham's American driver Alexander Rossi a seat and the other shared initially with Lewis Williamson (who moved to GP3 with Status Grand Prix to complete the season) and latterly a driver from the Red Bull young driver programme that we should all watch with serious intent: Antonio Felix Da Costa.

Da Costa has impressed this season in WSR taking 4 victories and 166 points leaving him only 23 points short of Robert Frijns who won the Championship. Bear in mind however that he missed the first 5 races whilst Williamson deputised, he also went on to victory at the Macau Grand Prix taking pole and leading every lap of the race. All of this whilst taking 3rd place in the GP3 championship for Carlin and taking 3 victories throughout the season. I personally see the young Portugese driver taking charge of a Toro Rosso at some point throughout the 2013 season as a taster to his possible progression to a Red Bull Racing seat going forward. Da Costa got a taste of F1 when he piloted the RB8 at the Abu Dhabi Young Drivers test late in 2012 season.

With Horner at the helm Red Bull turned their attentions to providing him with the personnel needed to elevate the team to the top ranks.  Top of their shopping list was McLaren's Chief Designer, Adrian Newey who the previous owners Jaguar had also courted early in their gestation period.  Newey's achievments speak for themselves having had success throughout the 90's with both Williams and McLaren.  Newey penned cars took the Constructors Championships for Williams through 92-97 with 95 being the only blotch in an otherwise dominant period. In 1998 he won a further Constructor's title with McLaren and although the MP4/14 of 1999 was clearly aerodynamically superior to the rest of the field a string of retirements for David Coulthard meant that only the drivers title went to Mika Hakkinen / McLaren that year.  As F1 moved into the next decade Ferrari became a dominant force with Schumacher at the helm of the Scarlet red machines.  Adrian's appointment at Red Bull in 2005 marked the teams desire to succeed at the highest level and would lead to further success for Newey when the rules drifted to his arena in 2009.

Geoff Willis spent a short period with the team during 2007-2009 as Technical Director once again reprising a relationship that had seen him work with Newey at both Leyton House and Williams.

Red Bull realised to be successful in F1 that personnel was not the only requirement and Red Bull would need to invest in high end technologies.  Over the past 8 years the team have amassed an arsenal of equipment and facilities whilst building relationships with companies that wish to drive their own products/brands forward.  This appears to be part of Red Bull's success with them working in partnership with their suppliers allowing each other to understand the processes involved so that both may benefit.  


Part of the initial purchase from Jaguar Racing included a Wind Tunnel facility that Ford had purchased back in 2003 and had set the task of refurbishing. The tunnel dated back to the 1940's and was initially used by the MOD to develop aircraft and had also been used to develop Concorde, the upgrade to the facility took 2 years including the installation of a rolling road bringing the facility inline with some of the top tier teams. The tunnel is full scale and although the regulations now limit models to 60% they could initially use the full capabilities when the tunnel was completed. All F1 teams are notoriously secretive about the inner workings of their Wind Tunnel facilities and only a handful of video's/images show what lies inside. I'll talk about their previous Wind Tunnel facilities at Bicester a little later in the article. The Wind Tunnel however is just one of the tools required by a contemporary F1 team to use and is perhaps where Red Bull's investment paid off at a time when F1 was moving from track testing to simulation in order to fulfill the budgetary requirements.

Remarking on the changes invoked from the Jaguar days Christian has had this to say: 'We set clear goals in each area and matched those objectives by investing in the facility, in tools or in personnel. It is absolutely true to say that a totally different culture exists today.”

Just as important as the real world environment of the Wind Tunnel is CFD (Computational Fluid Dynamics) this is a process that allows the designers to test the fluidic nature of their CAD models. The process can be used as a first step to realising the advantages or flaws to a given design without the intrinsic costs of actually building the part(s). This saves time, materials and inevitably cost as many iterations of the same model can be tested for validity before processing the part(s) for manufacturing and testing. Just as in the real world Wind Tunnel CFD affords the team the options of straightline testing or testing cornering / braking. The latter of course will yield a far more complicated result and so the time in which this is achieved is also raised.

In order to fulfill the needs of the team their own in house computing cluster uses hardware from HP and IBM. All F1 teams are tight lipped about the power they have at hand in terms of computing power but the FOTA RRA was initially designed to limit the Teraflops available in a cluster to the teams (A Teraflop is 1 trillion floating point calculations a second) the FOTA agreed limit isn't available on the open market but I believe it to be between 60-80 teraflops. Of course as with everything the engineers are always wanting more power and so in 2006 they formed an alliance with Platform Computing in order to help streamline their processes. Platforms load sharing facilty schedules workloads and proportions resources to prioritise the needs of the team. As we all know both Red Bull Racing and Scuderia Toro Rosso are no longer part of the association and so can live outside of their rules. (This doesn't mean to say they are but it is possible).

The process of transferring the CAD data to CFD can be a time consuming matter with the process of meshing the model for CFD usage taking huge quantities of time. Red Bull have a partnership with ANSYS and use their Fluent package to run CFD allowing the team to use Immersed Boundary Methods (IBM) which takes a short cut to the production of the final CFD model. IBM fills the gaps from the CAD model with an accurate representation of the final structure allowing the designers to model and run more CAD/CFD projects in a short time frame. All of this would not be possible without the high performance computing platform that Red Bull have access to utilising Siemens NX software. The NX software covers CAD/CAE/CAM (Computer Aided Design/Computer Aided Engineering/Computer Aided Manufacturing). CAD allows the designer an environment in which to build a representation of the part. CAE allows the part to be virtually tested for vulnerability, testing it's capacity to take stress under load or vibration. CAM takes care of the manufacturing element of the part giving the information to a plethora of in house CNC machines that produce the parts.

3D printing (Via 3D Systems) has now become an integral part of developing an F1 car, leading to both reduced lead times, cost reduction but most importantly the construction of previously un-manufacturable components/parts. The ethos is not new and has been used in F1 since the late 90's, but as time has marched on the processes have become more intricate and rewarding. In a world where the margin between a winning car and a losing one are so small this process helps to bridge a gap. Working from CAD a team can print parts at a alarming rate allowing them to be tested in the real world environment. Furthermore many of the none structural components of the full scale car are also manufactured in this way allowing many permutations to be used at the track. The team also use 3D printing in order to produce casts that are used in the production of Gearboxes and so forth. Due to the way in which 3D printing uses the materials any products that do not meet the requirements of the team can be destroyed and around 80% of the raw material re-used.

Their association with Hexagon Metrology affords the team highly precise 3D scanning capabilities through the use of ROMER Absolute Arms which mated with their CMS108 Laser Line Scanner allows time to be spent productively elsewhere. This allows vast quantities of parts to be checked against their original CAD designs for imperfections in a timely fashion. The Arm is also none intrusive, scanning the part(s) without contact meaning it doesn't deform under load allowing for a more accurate result.

With hand held measuring tools from Leica the team are able to accurately measure dimensions to a level that seems intangible. This bears fruit when we bear in mind that Red Bull use the tool across the whole platform and in combination with the likes of the products mentioned above from design, to scale modelling to full production. (Case Study on the use of Leica products by RBR - http://metrology.leica-geosystems.com/downloads123/m1/metrology/general/case%20studies/Red%20Bull%20Racing_Milton%20Keynes_CS_en.pdf )


Testing parts on the scale and full car are still a worthy variable to have at a teams disposal and so the use of a 7 post rig is used in order to evaluate the car as a whole. The test rig uses hydraulic actuators in order to put the car under load, this movement exerted on the car can show any weaknesses that may scupper performance. As with the driver simulator it is possible to use data collected from the circuit to create an environment that the car will be placed in.


Another area of crucial investment from Red Bull Technology has been the driving simulator, it's nothing like being sat in front of your xbox with a steering wheel as the drivers are seated in a full blown Red Bull Chassis. All of the controls mimic those on the current car to allow the driver to train like he would at the real circuit. Data that the teams have collected in the past or during a current race weekend can also be used in the simulator in order to extract more performance through setup. Teams use their simulators during race weekends in order to assist the team at the circuit make informed choices and/or strategy calls. The Chassis is mounted to a 6 post rig that is actuated to simulate the effects felt when on track, with a 180 degree field of vision further immerses the driver in the experience. Data extracted from the track before has been used to accentuate the depth of the experience. This is also a great place for driver assessment as data can be shown to the them in order for them to adjust their approach. It also allows for the drivers to be pooled together and assessed for their own strengths and weaknesses, a vital tool when selecting new drivers with limited on track testing.

The Cars

2005 - RB1

2005 saw regulations alter the racing with the drivers only allowed a singular set of tyres for both qualifying and the race. The impact of this would be far reaching and require not only great skill on behalf of the driver but careful aerodynamic and mechanical planning in order to extract performance and life from the grooved Michelin / Bridgestone tyres. The technical story of the year (and 2006) was Renault's Mass Damper: housed in the nosecone it allowed the team to alter the way in which the aerodynamic platform of the car behaved. Attenuating the Suspension and Front Wing it allowed the car to behave much more sure footedly giving a better contact patch for the Front tyres thus extracting better performance over a larger timeframe.

Above: The RB1 at pre season testing in Jerez

If I were to compare the RB1 aerodynamically to the Renualt (R25) and McLaren (MP4-20) of the time we can see that the RB1 featured little Sidepod undercut. Although they had Aero appendages sprouting from the rear of the Sidepod to help control the rear wheel airflow they weren't as refined as their opposition. The likes of Renault and McLaren were using multi element sections in order to make those regions more efficient.

Above: The Renault R25 from 2005

Above: The McLaren MP4-20

The regulations of that year had forced the designers to raise the Front Wing giving the impression the Wing had sagged in the centre. At the rear of the car we can see that the RB1's Rear Wing lacked the design prowess of it's more equipped rivals with the Red Bull team sporting a far less complex design.

The teams aerodynamic deficiencies didn't however stop them from producing some great performances. Coulthard notched up two fourth place finishes and tallied a total of 24 points throughout the season meanwhile Klein and Luizzi in combination managed a further 10 points.

Above: The team made incremental updates to the RB1 throughout 2005 with the largest upgrade arriving later on in the season at Hungary where they slimmed the rear bodywork and added a Shark Fin to the rear of the Engine Cover

2006 - RB2


For 2006 Red Bull further increased their presence within F1 when they purchased the Minardi team renaming the team Toro Rosso. For 2006 a switch would be made from V10's to V8's in order to reduce the power output being created by the teams. Minardi had already come to an arrangement with the FIA to continue using the Cosworth V10 for 2006 but in a more restricted capacity. This allowed the Toro Rosso team to simply use the RB1 chassis design reducing costs across the board for Red Bull. Red Bull Racing meanwhile made the switch to V8's with the assistance of Ferrari power. The RB2 replaced it's 2 tier Front Wing with a 3 tier one and altered the design of the Rear Wing for more efficiency. A much bulkier nosecone donned the RB2 than that of the R26 or MP4-21. 

Above: Kimi Raikonnen at the wheel of his McLaren MP4-21

Above: Renault's 2006 challenger the R26

The R26 featured Front Wing cascades as the teams realised the need to control the airflow up and around the front wheel/tyre. Meanwhile Ferrari adopted Bridge Cascades across the width of the Front Wing in order to better alter the airflow over the rest of the car.

Above: Michael Schumacher driving the Ferrari 248F1

Like the Renault team Red Bull adopted a V Keel on the front of their 2006 challenger in order to allow good adjustability whilst maintaining an aerodynamic advantage. The flexibility of some of the front teams Rear Wing planes were bought into question early on in the season and the FIA stepped in at San Marino adjusting the vertical load tests. The idea behind the flexing rear wing was to allow the gap between the top and mainplane to be reduced resulting in the Wing stalling and reducing drag for a higher top speed.

The complexity of the rear bodywork on the RB2 failed to match that of their rivals and with reliability issues from poor cooling of the Ferrari engine the team failed to match the points haul of 2005. The team abandoned the development of the RB2 early into it's lifespan with the imminent arrival of Adrian Newey from McLaren tasked with designing the RB3. David Coulthard once again produced the best results from the RB2 with the Scot even driving to a podium finish at Monaco.

2007 - RB3 

Above: Mark Webber negotiates the streets of Monaco in his RB3

2007 saw a singular supply of tyres via Bridgstone as Michelin departed the sport, this also bought rise to the 2 compound rule that we still have today. In order to drive down ever increasing demands on engine suppliers to build superior engines the FIA also introduced the engine freeze (Homologation). Steps were also taken to reduce spend on track testing with a 30,000 km limit placed on teams testing throughout the season.
Red Bull took Mark Webber as their other driver for the 07 campaign, the Australian driver returning to the team having previously driven for the then Jaguar. Meanwhile Antonio Liuzzi would line up for the sister team Toro Rosso, accompanied by the US driver Scott Speed.
Red Bull Racing's contract with Ferrari for supply of their V8 engines was also moved to the Toro Rosso team as Red Bull ushered in Renault engines.

 
Controversy surrounded the two Red Bull teams throughout 2007 as many teams (led by Spyker) argued that the RB3 and STR2 were essentially the same car. Red Bull Technology had produced both chassis for the teams and although the designs were intrinsically the same there were nuances that made them differ. Chiefly the aforementioned difference in engine supply which would make for subtle differences to not only power but weight and cooling requirements.

This was to be the start of Red Bull's ascendence to F1 notoriety and marked a distinct difference in approach to the other leading teams. Scuderia Toro Rosso could be used as not only a test bed for future talent from their young driver programme but also allowed the design team to try/test more components over a wider spectrum.

Both the RB3 & STR2 featured much deeper Sidepod undercuts and sported the half moon Sidepod airflow conditioners that had featured on the BAR throughout 2006. Both cars seemed infinitely more shrink wrapped than their predecessors and featured more intricate rear end aero 'flip ups'. This signaled the influence of Adrian Newey as he bought his expertise to the Red Bull Technology setup. Red Bull Technologies Achilles heal for 2007 was their seamless shift gearbox mated to both cars, fraught with problems throughout the season for both teams it was the cause of many DNF's.

Red Bull and Toro Rosso concluded the season in 5th and 7th respectively but the largest ray of hope for the outfit was the young German, Sebastian Vettel. Seb had been BMW's test driver during the 2006 season and had impressed when being placed behind the wheel in testing. He got his F1 debut at the US Grand Prix replacing the injured Kubica and became the youngest driver to score points in F1 taking 8th place for 1 point. He was released by BMW in order to take a drive with Toro Rosso but struggled through the first few races as he adapted to the STR2. However in a rain hit race at Fuji he would find himself in 3rd place behind Lewis Hamilton's McLaren and the sister car of Mark Webber. This was however not to be his crowning glory as under safety car conditions the young German made a mistake and rear ended Webber. Angered by Seb's inexperience Mark gave an interview to ITV stating: "It's kids isn't it... kids with not enough experience – you do a good job and then they fuck it all up."

The mistake was fairly costly for Red Bull in general and although the extra 8 points for Webber wouldn't have been enough for them to leapfrog Williams the same couldn't be said for Toro Rosso who with another 6 points would have jumped ahead of Toyota.
Unfazed by the media furore that would follow Vettel produced another emphatic performance in China scoring 4th place with his team mate Liuzzi also scoring points just behind in 6th.

2008 - RB4


The RB4 showed the further reaching grasp of Adrian Newey over the Red Bull project with the car sporting a much lower Sidepod and the engine cover encapsulating the components much tighter. The RB4 arrived at testing with a Shark Fin engine cover something that the other teams duly noted and went off to produce their own iterations in order to enhance their packages. The team now with a year shod on the Bridgstone tyres perhaps had a better grasp of the task at hand in regard to their aero influence too. The usual in season updates occurred with the likes of a perforated 'Bridge Wing' that featured slots at it's outer extremities to boost it's effectiveness and helped to flex the Front Wing assembly. This lead to the legality of flexing Front Wings being bought into question with the FIA who duly adjusted their stance and the teams rectified their designs. To cope with the regulation changes Red Bull altered the central portion of the Bridge Wing in order to add rigidity and then latterly altered the Endplate Horizontal blades and added additional vertical turning vanes underneath the Mainplane.

 
At the start of 08 BMW Sauber had introduced Nosecone Winglets which helped to manage and vorticise the airflow downstream. Red Bull added their own appendages in this region later on in the season at the Inaugural Singapore night race.

Mark Webber outscored his more seasoned colleague throughout the season but it was Coulthard who had the best result of the season taking the podium and 3rd place at Montreal. 

Above: Sebastian Vettel drives his STR3 through the tunnel in Monaco

Meanwhile over on the Toro Rosso side of the fence the team started their 2008 campaign with a B spec STR2 with the STR3 not being competitively ready until round 6 in Monaco. This led to a poor start to the season with the only points being scored by the newly appointed Sebastian Bourdais at Australia. Sebastian Vettel was a revelation in the 2008 season scoring 35 of the 39 points accumulated by the Toro Rosso team. The crowing glory however came in Monza when Vettel and the team beat the odds to score Red Bull's first victory in F1 ahead of their lead team.


In Part 2 I look at 2009 through until 2012 the years that have defined Red Bull Racing as a force to be reckoned with within F1.  However as we have learnt above every story must have a beginning and although the results didn't always meet their ambitions in the formative years it put them in good stead for what lay ahead.
Read more

Total Pageviews